QB288 V2 Rspec Quantum Board

New Product

$79.00 $99.00

QB288 V2 R spec Quantum Boards

QB 288 V2 Rspec are made USA by Horticulture Lighting Group. Each board has 272 highest flux and lowest voltage bin Full Spectrum LM301B LED. 16 Osram SSL 660nm Deep Red LED enhance spectrum and unbeatable performance.

No Thermal Interface Material or paste is required.

Specifications

• 272pcs Samsung LM301B Bin Diodes, 16 Osram SSL Deep Red
• Connectors rated 300V 9A
• Dimensions 6.833" x 11.25
• Max current per board 3000mA @ 54VDC
• Weight 0.5 lbs

Spectrum

• 3500k Samsung LM301B Bin Diodes, 16 Osram 660nm Deep Red
• CCT 3150-3250
• CRI (Ra) 90

May require an Aluminum plate or heatsink if running 75+ watts. Heatsink requirements depends on application and power.

Datasheet of Samsung LM301B Datasheet used in R spec Quantum Board ®

QB288 V2 Quantum Board

288 LM301B LED

$65.00 $99.00

QB288 V2 Quantum Boards

QB 288 V2 are made USA by Horticulture Lighting Group. Each board has 288 highest flux and lowest voltage bin for an unbeatable performance.

High efficiency boards designed for DIY projects. Available in 3000K and 4000K. No Thermal Interface Material or paste is required.

Datasheet

Specifications

• 288pcs Samsung 301B Bin Diodes
• Connectors rated 300V 9A
• Dimensions 6.833" x 11.25
• Max current per board 3000mA

Flux Characteristics with QB 288 V2 3000K, S6 Bin at 55C

May require an Aluminum plate or heatsink if running 75+ watts. Heatsink requirements depends on application and power.

QB288 V1 Quantum Board

QB288 V1

$45.00 $75.00

QB288 V1 Quantum Boards

QB 288 3000K are made in USA

High efficiency boards designed for DIY projects. No Thermal Interface Material or paste is required.

Specifications

• Connectors rated 300V 9A
• Estimated LER 321.60 lm/W
• Estimated QER 4.86 µmol/J
• Dimensions 6.833" x 11.25
• Max current per board 3000mA

Flux Characteristics with QB 288 V1 3000K

May require an Aluminum plate or heatsink if running 60+ watts. Heatsink requirements depends on application and power.

QB120 V2 Quantum Boards

Avaialble on Amazon

$132.00 $200.00

QB120 Quantum Boards (4 Pack)

High efficiency boards designed for DIY projects. Each board can be powered up to 70 watts. No Thermal Interface Material or heatsink is required. Does not work with Slate series Heatsinks

Specifications

• 4 piece QB 120 LED Boards
• 120pcs Samsung LM301B LED per board
• 2 Molex Connectors, Push-Button Type
• Dimensions 280mm x 240mm
• Max current per board 2800mA

Connector Options

Board's power wires can optionally be soldered.

• Molex Connector

Wire can be pushed into the connector. To unmate,  push down lever on the housing to allow the wire to be disengaged. Rated 300V 9A. Max 10 boards in series wiring.

Driver Options

Single Board

GSC40B-1400 for US with IEC 60320/C7 Power Cord.
OWA-60U-24 for US
LPC-35-1400
LPC-60-1750
LPF-40-24 or LPF-40D-24
LPF-60 -24 or LPF-60D-24
HLG-40H-24
HLG-60H-24

GSC40E-1400 for EU

LPC-100-2100 - 2x QB 120 in series
LPF-90D-48 or LPF-90-48 - 2x QB 120 in series
HLG-80H-48 - 2x QB 120 in series
HLG-100H-48 - 2x QB 120 in series
HLG-120H-48 - 2x QB 120 in series

HLG-240H-C2100 - 4x QB 120 in series

QB132 V2 Quantum Boards

Avaialble on Amazon

$135.00 $200.00

QB132 Quantum Boards (4 Pack)

High efficiency boards designed for DIY projects. Each board can be powered up to 75 watts. No Thermal Interface Material or heatsink is required. Does not work with Slate series Heatsinks.

Specifications

• 4 piece QB 132 LED Boards
• 132pcs Samsung LM301B LED per board
• 1 Molex Connectors, Push-Button Type
• Dimensions 300mm x 225mm
• 36V DC. Max current  2100mA

Board's power wires can optionally be soldered.

• Molex Connector

Wire can be pushed into the connector. To unmate,  push down lever on the housing to allow the wire to be disengaged. Rated 300V 9A. Max 10 boards in series wiring.

Driver Options

• LPF-60-36 - 1x QB132
• HLG-185H-C1400 - 4x QB 132 in series
• HLG-240H-C1750 - 4x QB 132 in series

For more driver options check here

QB132 V1 Quantum Boards

4Pcs QB132 Boards

$109.00 $200.00

QB132 V1 Quantum Boards (4 Pack)

High efficiency boards designed for DIY projects. Each board can be powered up to 75 watts. No Thermal Interface Material or heatsink is required. Does not work with Slate series Heatsinks.

Specifications

• 4 piece QB 132 LED Boards
• 1 Molex Connectors, Push-Button Type
• Dimensions 300mm x 225mm
• 36V DC. Max current  2100mA

Board's power wires can optionally be soldered.

• Molex Connector

Wire can be pushed into the connector. To unmate,  push down lever on the housing to allow the wire to be disengaged. Rated 300V 9A. Max 10 boards in series wiring.

Driver Options

• LPF-60-36 - 1x QB132
• HLG-185H-C1400 - 4x QB 132 in series
• HLG-240H-C1750 - 4x QB 132 in series

For more driver options check here

QB144 V2 Quantum Boards

4Pcs QB144 Boards

$125.00

QB144 Quantum Boards (4 Pack)

High efficiency boards designed for DIY projects. Each board can be powered up to 75 watts. Can use used with Pin Heatsink or Extruded Aluminum. 36V design makes it ideal upgrade for COB on Pin Heatsink.

Includes

• 4 piece QB 144 LED Boards
• 4pcs Thermal Adhesive Pads

Specifications

• 144pcs Samsung LM301B LED per board
• 1 Molex Connectors, Push-Button Type
• Board Size 95.25mm X 70.36mm , 3.75 inches  X 2.77 inches
• 36V DC. Max current  2100mA

Thermal Management and Installation

Pin Heatsink or Extruded Aluminum is Required. Board will overheat and fail without heatsink. Clean heatsink with isopropl alcohol. Remove liner from adhesive pad and apply on back of board. Remove liner from other side and apply to heatink.

Apply pressure on corner of board without touching the LED. This will ensure board and heatsink get bonded properly with the adhesive pad. Adhesive pad is permanent  and cannot be removed or adjusted.

Driver Options

• LPF-60-36 - 1x QB144
• LPF-40-36 - 1x QB144
• LPC-60-1050 - 1x QB144
• HLG-60H-36 - 1x QB144
• HLG-40H-36 - 1x QB144
• HLG-185H-C1400 - 4x QB 144 in series
• HLG-240H-C1750 - 4x QB 144 in series
• HLG-320H-C2100 - 4x QB 144in series

Wire can be pushed into the connector. To unmate,  push down lever on the housing to allow the wire to be disengaged. Rated 300V 9A. Max 10 boards in series wiring.

QB11 Quantum Board

450nm, 470nm, 521nm 630nm, 660nm

$25.00 $49.00

QB11 Quantum Boards Deep Red

High efficiency Deep Red Strip

Test Report

55.6% radiometric efficiency at 350mA (4.75 watts radiometric output with 8.54 watts electrical Input)

Specifications

• 11pcs High Power Deep red 660nm Diodes
• Peak wavelength 660nm
• Forward Voltage 22.5+ VDC at 350mA, 24.70+ VDC at 700mA
• Dimensions 30mm x 560mm
• Max current per strip 1400mA
• Heatsink required for over 1050mA

QB11 Quantum Boards Red

High efficiency Red Strip

Specifications

• 11pcs High Power red 630nm Diodes
• Peak wavelength 630nm
• Forward Voltage 23+ VDC at 350mA, 25.5+ VDC at 700mA
• Dimensions 30mm x 560mm
• Max current per strip 1400mA
• Heatsink required for over 1050mA

QB11 Quantum Boards Blue

High efficiency Blue Strip

Specifications

• 11pcs High Power Blue 450nm Diodes
• Peak wavelength 450nm
• Forward Voltage 33.80+ VDC at 700mA
• Dimensions 30mm x 560mm
• Max current per strip 1400mA
• Heatsink required for over 1050mA

Molex Connector

QB 11 Strips have Molex Connectors. +ve and -ve on opposite ends of strip. Wire can be pushed into the connector. To unmate,  push down lever on the housing to allow the wire to be disengaged. 

Driver Options

Meanwell LLD H are a great way of using standard power supplies to power QB 11 strips. These step down DC-DC drivers are available in 300mA, 350mA, 500mA, 600mA, 700mA, 1200mA. LDD-xxxHW option comes with wires attached. Also available in Pin and SMT style

Design considerations

• Output voltage will always step down by 3 volts from input DC voltage. This means if input in 48 VDC then you cannot max 45VDC in output. Ensure the input is a minimum of QB 11 forward voltage and add another 3 volts
• LLD H 300mA, 350mA, 500mA, 600mA, 700mA options can accept 2 ~ 52VDC input range. 1200mA option can accept only 2 ~ 46VDC
• QB 11 Deep red and Blue have different forward voltage. Blue and Deep red cannot be run in parallel together. Blue has as Higher forward voltage.

Wiring example with QB 288, Meanwell HLG-120H-54 Driver and QB 11 powered through LDD-700HW

LDD-1200HW

Other Drivers for Single QB 11 Strip or multiple in parallel

Drivers for Multiple QB 11 Strip in series

QB18 V2 Quantum Board

Red Supplement

$39.00

QB 18 V2 LED board is designed to supplement full spectrum white. Each Board has total 18 high power LED.

Specifications

Requires heatsink for for use over 1050mA. Can be installed on Slate 7 with thermal tape

Single Board

LPC-35-1400
LPF-40-24 or LPF-40D-24
HLG-40H-24

2 Boards

LPF-90D-48 or LPF-90-48 - 2x QB 96 in series
HLG-80H-48 - 2x QB 96 in series

2 Boards

LPC-100-2100 - 2x QB 18 in series
LPF-90D-48 or LPF-90-48 - 2x QB 18 in series
HLG-80H-48 - 2x QB 18 in series
HLG-100H-48 - 2x QB 18 in series

4 Boards

HLG-240H-C2100 - 4x QB 18 in series

QB96 Elite V2 Engine

High Power LED Board

$69.00 $99.00

QB96 Elite V2 Quantum Board Engine

QB96 Elite V2 is a white LED Board with boosted red spectrum. Each QB 96 Elite board has 64 High power White, 16 Red (630nm) and 16 Deep Red (660nm). QB96 Elite V2 offers a wider spectrum than standard 70 CRI, 80 CRI and 90 CRI LED.

Includes

• QB 96 Elite Quantum Board
• Thermal Pad, Tacky - Both Sides  
• SSTX Heatsink
• M3 Screws for Board

Specifications

• QB 96 Elite Board Size 95.25mm X 70.36mm , 3.75 inches  X 2.77 inches
• Max 4200mA with SSTX Heatsink and Thermal Pad
• Absolute max 6000mA
• Heatsink 125mm x 125mm base, 170mm x 170mm Flared side
• M3 screw holes for board, M4 for mounting engine.

Thermal Pad

3M Acrylic Interface Pad 5590H OR Bergquist GAP PAD HC 3.0 is included. Remove liner on one side of die cut thermal pad, align screw holes with board and apply pad to board, remove liner from the other side and install board to heatsink. Thermal pad is not permanent and allows rework.

Note: Thermal pad is Tacky and not adhesive. Board requires screws to ensure board is securely mounted to heatsink.

(White) 3M Acrylic Interface Pad 5590H

(Blue) Bergquist GAP PAD HC 3.0

Flux Characteristics at 55C

Lens Compatibility

Lens PL1758CV

Gasket KGAS04

Driver Recommendations

Single QB 96 Elite V2

• HLG-80H-54
• HLG-100H-54
• HLG-120H-54
• HLG-150H-54
• HLG-185H-54
• HBG-160-60
• HBG-200-60
• LPC-100-1750
• LPF-90-54 , LPF-90D-54
• ELG-150-54, ELG-200-54 recommended for 200+VAC only

Two QB 96 Elite V2 in series

• HLG-320H-C2800
• HLG-240H-C2100
• HLG-185H-C1400
• HLG-120H-C1050
• ELG-240-C2100, ELG-200-C1750, ELG-300-M   for 200+ VAC only

Four QB 96 Elite V2 in series

• HLG-480H-C2100
• HLG-320H-C1400

Multiple QB 96 Elite V2 in parallel

• HLG-240H-54 with 2 or more boards in parallel
• HLG-320H-54 with 2 or more boards in parallel
• HLG-480H-54 with 3 or more boards in parallel
• HLG-600H-54 with 3 or more boards in parallel
• ELG-240-54 recommended for 200+VAC only

QB96 Elite V2 Quantum Board

High Power LED Board

$54.00 $99.00

QB96 Elite V2 Quantum Board

QB96 Elite V2 is a white LED Board with boosted red spectrum. Each Board is powered by 64 high power white LED, 16 630nm Red LED and 16 660nm Deep Red LED. QB96 Elite V2 offers a wider spectrum than standard 70 CRI, 80 CRI and 90 CRI LED.

Heatsink and Thermal Pad required to run board over 500mA (25 watts)

Includes

• QB 96 Elite Quantum Board
• Thermal Pad, Permanent Adhesive - Both Sides  

Note: Thermal pad is Permanent adhesive. Once installed it cannot be removed. Board must be installed on a 120mm diameter or bigger pin heatsink or suitable Aluminum extrusion.

Specifications

• Board Size 95.25mm X 70.36mm , 3.75 inches  X 2.77 inches
• Absolute max 6000mA

Flux Characteristics at 55C

QB288 V2 Rspec & Slate 2 Single Combo

Board & Heatsink

$94.00 $225.00

QB288 V2 Rspec & Slate 2

High efficiency boards designed for DIY projects. No Thermal Interface Material or paste is required.

Specifications

• One QB288 V2 Rspec
• One Slate 2 Single heatsink. Black
• Connectors rated 300V 9A
• Dimensions 6.833" x 11.25
• Max current per board 3000mA @ 54VDC

 Datasheet of Samsung LM301B Datasheet used in R spec Quantum Board ®

QB288 V2 Rspec & Slate 2 Double Combo

Board & Heatsink

$185.00 $225.00

QB288 V2 Rspec & Slate 2 Double

High efficiency boards designed for DIY projects. No Thermal Interface Material or paste is required.

Specifications

• 2x QB288 V2 Rspec
• One Double Slate 2 heatsink. Black or clear aluminum
• Connectors rated 300V 9A
• Dimensions 6.833" x 11.25
• Max current per board 3000mA @ 54VDC

Datasheet of Samsung LM301B Datasheet used in R spec Quantum Board ®

QB288 V2 Rspec & Slate 2 Triple

Horticulture Lighting Group

$279.00 $399.00

QB288 V2 Rspec & Slate 2 Triple

Specifications

• Three QB 288V2 Rspec
• One Triple Slate 2 heatsink
• Connectors rated 300V 9A
• Dimensions 6.833" x 11.25
• Max current per board 3000mA @ 54V

 Recommended driver(350Watts max) for 3x QB 288 boards in series HLG-320H-C1750A

Datasheet of Samsung LM301B Datasheet used in R spec Quantum Board ®

QB288 V2 & Slate 2 Single Combo

Board & Heatsink

$84.00 $225.00

QB288 V2 Quantum Board & Slate 2

High efficiency boards designed for DIY projects. No Thermal Interface Material or paste is required.

Specifications

• One QB288 V2 Board made by Samsung with 301B LED
• One Slate 2 Single heatsink. Black
• Connectors rated 300V 9A
• Dimensions 6.833" x 11.25
• Max current per board 3000mA

Flux Characteristics with QB 288 V2 3000K, S6 Bin at 55C

QB288 V2 & Slate 2 Double Combo

Board & Heatsink

$169.00 $225.00

QB288 V2 Quantum Board & Slate 2 Double

High efficiency boards designed for DIY projects. No Thermal Interface Material or paste is required.

Specifications

• 2x QB288 V2 Boards made by Samsung with 301B LED
• One Double Slate 2 heatsink. Black or clear aluminum
• Connectors rated 300V 9A
• Dimensions 6.833" x 11.25
• Max current per board 3000mA

Flux Characteristics with QB 288 V2 3000K, S6 Bin at 55C

QB288 V1 & Slate 2 Single Combo

QB288 V1 Combo

$64.00 $99.00

QB288 V1 Quantum Board & Slate 2

High efficiency boards designed for DIY projects. No Thermal Interface Material or paste is required.

Specifications

• One QB288 V1 Board
• One Slate 2 Single heatsink. Black
• Connectors rated 300V 9A
• Dimensions 6.833" x 11.25
• Max current per board 3000mA

Flux Characteristics with QB 288 V1 3000K, S6 Bin at 55C