$135.00 $200.00
High efficiency boards designed for DIY projects. Each board can be powered up to 75 watts. No Thermal Interface Material or heatsink is required. Does not work with Slate series Heatsinks.
Board's power wires can optionally be soldered.
Wire can be pushed into the connector. To unmate, push down lever on the housing to allow the wire to be disengaged. Rated 300V 9A. Max 10 boards in series wiring.
For more driver options check here
View full product details$125.00
High efficiency boards designed for DIY projects. Each board can be powered up to 75 watts. Can use used with Pin Heatsink or Extruded Aluminum. 36V design makes it ideal upgrade for COB on Pin Heatsink.
Pin Heatsink or Extruded Aluminum is Required. Board will overheat and fail without heatsink. Clean heatsink with isopropl alcohol. Remove liner from adhesive pad and apply on back of board. Remove liner from other side and apply to heatink.
Apply pressure on corner of board without touching the LED. This will ensure board and heatsink get bonded properly with the adhesive pad. Adhesive pad is permanent and cannot be removed or adjusted.
Wire can be pushed into the connector. To unmate, push down lever on the housing to allow the wire to be disengaged. Rated 300V 9A. Max 10 boards in series wiring.
View full product details
$54.00 $99.00
QB96 Elite V2 is a white LED Board with boosted red spectrum. Each Board is powered by 64 high power white LED, 16 630nm Red LED and 16 660nm Deep Red LED. QB96 Elite V2 offers a wider spectrum than standard 70 CRI, 80 CRI and 90 CRI LED.
Heatsink and Thermal Pad required to run board over 500mA (25 watts)
Note: Thermal pad is Permanent adhesive. Once installed it cannot be removed. Board must be installed on a 120mm diameter or bigger pin heatsink or suitable Aluminum extrusion.
Flux Characteristics at 55C
VDC | Current (mA) | Watts at Board | μmoles/joule at Board (55C) |
51.5 | 1400 | 72 | 2.60 |
52.2 | 1750 | 91 | 2.52 |
53.4 | 2400 | 128 | 2.40 |
54 | 2800 | 151 | 2.36 |
55 | 3400 | 187 | 2.32 |
56 | 4000 | 224 | 2.25 |
View full product details
$69.00 $99.00
QB96 Elite V2 is a white LED Board with boosted red spectrum. Each QB 96 Elite board has 64 High power White, 16 Red (630nm) and 16 Deep Red (660nm). QB96 Elite V2 offers a wider spectrum than standard 70 CRI, 80 CRI and 90 CRI LED.
3M Acrylic Interface Pad 5590H OR Bergquist GAP PAD HC 3.0 is included. Remove liner on one side of die cut thermal pad, align screw holes with board and apply pad to board, remove liner from the other side and install board to heatsink. Thermal pad is not permanent and allows rework.
Note: Thermal pad is Tacky and not adhesive. Board requires screws to ensure board is securely mounted to heatsink.
(White) 3M Acrylic Interface Pad 5590H
(Blue) Bergquist GAP PAD HC 3.0
Flux Characteristics at 55C
VDC | Current (mA) | Watts at Board | μmoles/joule at Board (55C) |
51.5 | 1400 | 72 | 2.60 |
52.2 | 1750 | 91 | 2.52 |
53.4 | 2400 | 128 | 2.40 |
54 | 2800 | 151 | 2.36 |
55 | 3400 | 187 | 2.32 |
56 | 4000 | 224 | 2.25 |
View full product details
$759.00 $899.00
HLG 600W LED kit has a output equivalent of 1000W DE HPS. 600W Kit is powered with our custom designed high efficiency QB288 V2 R spec Quantum Board using Samsung LM301H LED
Dimensions 740mm x 395mm
DOWNLOAD 600W KIT ASSEMBLY INSTRUCTIONS
Power | 620+ Watts |
Voltage Range | 120-277 VAC |
Flowering Footprint | 5' X 5' |
Veg Footprint | 6' X 7' |
System PPF Efficacy | 2.5 μmol/joule |
Total output | 1525+ PPF |
Weight | 25 lbs |
This product does not include any manual. Please buy HLG 550 if you are not sure.
50 K ohm Potentiomter(included) can be wired across Dim + and Dim - for manual dimming.
NOTE:
Boards should be wired in series with the driver for maximum output
$349.00
260 Watt Lamp Kit. High Efficiency QB288 V2 spec powered with Samsung LM301H and Blue 470nm LED. Suited for veg lighting. New updated Inventronics driver allows full range dimming with included potentiometer.
Dimmable | 135-280 Watts |
Length | 600mm |
Width | 205mm |
Veg Footprint | 4x4 sqft |
Recommended Flower Footprint | Use Rspec Instead |
DOWNLOAD 260W XL KIT ASSEMBLY INSTRUCTIONS
Datasheet of Samsung LM301H Datasheet used in R spec Quantum Board ®
No Thermal Interface Material is required between the LED board and the heatsink
Remove black plug on driver and use Philips head screw driver for dimming
NOTE: Boards should be wired in series with the driver for maximum output
View full product details
$485.00
320 Watt Lamp Kit. High Efficiency QB288 V2 R spec with Samsung LM301H LED. Suited for main light and supplement lighting. 3 ft long heatsink for a wider spread.
Length:891mm, Width:205mm
Dimmable | 100-340 Watts |
Length | 891mm |
Width | 205mm |
Veg Footprint | 5x5 sqft |
Recommended Flower Footprint | 2.5x5 sqft or 2x4 sqft |
DOWNLOAD 320W XL KIT ASSEMBLY INSTRUCTIONS
Lamp Efficacy with QB 288 V2 2.63 µmol/J
Board Level Efficacy with QB 288 V2 2.75 µmol/J
No Thermal Interface Material is required between the LED board and the heatsink
Remove black plug on driver and use Philips head screw driver for dimming
NOTE: Boards should be wired in series with the driver for maximum output
View full product details
$349.00
260 Watt Lamp Kit. High Efficiency QB288 V2 Rspec powered with Samsung LM301H . Suited for main light and supplement lighting. New updated Inventronics driver allows full range dimming with included potentiometer.
Dimmable | 135-280 Watts |
Length | 600mm |
Width | 205mm |
Veg Footprint | 4x4 sqft |
Recommended Flower Footprint | 3x3 sqft or 2x4 sqft |
DOWNLOAD 260W XL KIT ASSEMBLY INSTRUCTIONS
Lamp Efficacy with QB288 V2 Rspec 2.6 µmol/J
Board Level Efficacy with QB288 V2 Rspec 2.73 µmol/J
Datasheet of Samsung LM301H Datasheet used in R spec Quantum Board ®
No Thermal Interface Material is required between the LED board and the heatsink
Remove black plug on driver and use Philips head screw driver for dimming
NOTE: Boards should be wired in series with the driver for maximum output
View full product details
$369.00
260 Watt Lamp Kit. High Efficiency QB288 V2 Rspec. Suited for main light and supplement lighting. 3 ft long heatsink for a wider spread. New updated Inventronics driver allows full range dimming with included potentiometer.
Length:891mm, Width:205mm
Dimmable | 135-285 Watts |
Veg Footprint | 4x4 sqft |
Recommended Flower Footprint | 2x4 sqft |
DOWNLOAD 260W XL KIT ASSEMBLY INSTRUCTIONS
Lamp Efficacy with QB 288 V2 2.6 µmol/J
Board Level Efficacy with QB 288 V2 2.73 µmol/J
Datasheet of Samsung LM301H Datasheet used in R spec Quantum Board ®
No Thermal Interface Material is required between the LED board and the heatsink
Remove black plug on driver and use Philips head screw driver for dimming
NOTE: Boards should be wired in series with the driver for maximum output
View full product details
$197.50
135 Watt Lamp Kit. High Efficiency QB288 V2 spec powered with Samsung LM301H and Deep Red LED. Suited for main light and supplement lighting.
Dimmable | 60-150Watts |
Veg Footprint | 3x3 sqft |
Recommended Flower Footprint | 2x2 sqft |
Max Flower Footprint | 2x3 sqft |
DOWNLOAD 135W KIT ASSEMBLY INSTRUCTIONS
Lamp Efficacy with QB288 V2 Rspec 25 µmol/J
Board Level Efficacy with QB288 V2 Rspec 2.68 µmol/J
Datasheet of Samsung LM301H Datasheet used in R spec Quantum Board ®
No Thermal Interface Material is required between the LED board and the heatsink.
Remove black plug on driver and use Philips head screw driver for dimming
View full product details
$197.50
135 Watt Lamp Kit. High Efficiency QB288 V2 spec powered with Samsung LM301H and Blue 470nm LED. Suited for veg lighting.
Dimmable | 60-150Watts |
Veg Footprint | 3x3 sqft |
Recommended Flower Footprint | Rspec |
DOWNLOAD 135W KIT ASSEMBLY INSTRUCTIONS
No Thermal Interface Material is required between the LED board and the heatsink.
Remove black plug on driver and use Philips head screw driver for dimming
View full product details
$94.00 $225.00
High efficiency boards designed for DIY projects. No Thermal Interface Material or paste is required.
Datasheet of Samsung LM301H Datasheet used in R spec Quantum Board ®
View full product details
$185.00
High efficiency boards designed for DIY projects. No Thermal Interface Material or paste is required.
Datasheet of Samsung LM301H Datasheet used in R spec Quantum Board ®
View full product details
Sold Out
High efficiency waterproof LED BARDIY projects. Passive cooled 4ft length provides a great spread with minimal shadows.
4 x 2 ft Veg | SABER 100 |
4 x 2 ft Flower | 2x SABER 100 |
4 x 4 ft Veg | 2x SABER 100 |
4 x 4 ft Flower | 5x SABER 100 |
5 x 5 ft Veg | 3x SABER 100 |
5 x 5 ft Flower | 6x SABER 100 |
Each bar must be hung independently.
Hole in end cap for hanging with cable hanger included or to pass a mounting screw.
Sold Out
QB 18 V2 LED board is designed to supplement full spectrum white. Each Board has total 18 high power LED.
Voltage | 24+VDC |
Max Current | 2100mA |
LED | 18 pcs High Power |
Dimensions | 580mm X 45mm |
Connector | Molex |
Requires heatsink for for use over 1050mA. Can be installed on Slate 7 with thermal tape
Single Board
LPC-35-1400
LPF-40-24 or LPF-40D-24
HLG-40H-24
2 Boards
LPF-90D-48 or LPF-90-48 - 2x QB 96 in series
HLG-80H-48 - 2x QB 96 in series
2 Boards
LPC-100-2100 - 2x QB 18 in series
LPF-90D-48 or LPF-90-48 - 2x QB 18 in series
HLG-80H-48 - 2x QB 18 in series
HLG-100H-48 - 2x QB 18 in series
4 Boards
HLG-240H-C2100 - 4x QB 18 in series
View full product details$129.00
Details
Performance
View full product details
450nm, 470nm, 521nm 630nm, 660nm
Sold Out $49.00
High efficiency Deep Red Strip
55.6% radiometric efficiency at 350mA (4.75 watts radiometric output with 8.54 watts electrical Input)
High efficiency Red Strip
High efficiency Blue Strip
Molex Connector
QB 11 Strips have Molex Connectors. +ve and -ve on opposite ends of strip. Wire can be pushed into the connector. To unmate, push down lever on the housing to allow the wire to be disengaged.
Meanwell LLD H are a great way of using standard power supplies to power QB 11 strips. These step down DC-DC drivers are available in 300mA, 350mA, 500mA, 600mA, 700mA, 1200mA. LDD-xxxHW option comes with wires attached. Also available in Pin and SMT style
Design considerations
Wiring example with QB 288, Meanwell HLG-120H-54 Driver and QB 11 powered through LDD-700HW
View full product details
$29.00
Save on heatsinks. Purchase Heatsinks + Boards Combos
Slate 2 series is ideal for low cost high power QB 304 and QB 288 cooling applications.
View full product details
$50.00
THE PERFECT GIFT ANYTIME!
Shopping for someone else but not sure what is the right gift? Give them the gift of choice with a Horticulture Lighting Group eGift Card.
eGift cards are delivered by email and contain instructions to redeem them at checkout.
Our eGift Cards have no additional processing fees.
Ideal for Flowering/Full Cycle
Sold Out
HLG 550 PHASE OUT MODEL
(3 Year warranty is still in effect)
Click here to order the latest upgrade model, the NEW HLG 600.
Our HLG 550 V2 R Spec Commercial Indoor Horticulture LED grow light is designed to replace a single-ended 1000watt HID. Each HLG 550 V2 uses 4 of our custom designed full spectrum high efficiency white light quantum boards with Samsung LM301H and Deep Red LED 660nm . This unit is dimmable, with wattage output from 200 to 500 watts.
DOWNLOAD HLG 550 V2 R SPEC MANUAL
HLG 550 V2 Independent Lab Reports
View Report for Output/Efficiency
Power | 40-500 Watts |
Voltage Range | 100-277 VAC 50-60Hz |
LED | Samsung LM301H & Deep Red |
Flowering Footprint | 4.5' x 4.5' or 4' x 5' at 24" |
Veg Footprint | 6' x 6' at 36” |
System PPF Efficacy | 2.65 μmol/joule |
Total output | 1293 PPF |
Dimensions | 26" x 20" x 4" |
Recommended Mounting Height | 24-32 inches above canopy |
Watts to BTU Calculator, Cooling Requirement Calculator
Report for PPFD 24 inches 5' x 5'
Report for PPFD 18 inches 5' x 5'
Expect higher intensity and more even coverage in a grow tent, reflective area or a cross over with multiple lamps.
Check HLG 550 V2 B Spec for Veg spectrum option
Conforms to UL Std 1598
Certified to CSA Std C22.2#250.0
Expect higher intensity and more even coverage in a grow tent, reflective area or a cross over with multiple lamps.
View full product details
Sold Out
High efficiency boards designed for DIY projects. Each board can be powered up to 75 watts. No Thermal Interface Material or heatsink is required. Does not work with Slate series Heatsinks. Lumileds 2835HE LED
Board's power wires can optionally be soldered.
Wire can be pushed into the connector. To unmate, push down lever on the housing to allow the wire to be disengaged. Rated 300V 9A. Max 10 boards in series wiring.
For more driver options check here
View full product details$749.00 $799.00
Refurbished Lamps are tested and fully functional with HLG original components. May have Scratches and/or may have been previously used.
HLG 650R Commercial Indoor Horticulture LED grow light is designed to replace a double-ended 1000 watt HID lamp. 650 R uses 4 of our custom designed full spectrum high efficiency white light quantum boards with Samsung LM301H and Deep Red LED 660nm . This unit is dimmable, with wattage output from 60 to 610 watts.
View Report for Output & Efficiency
PPFD Chart at 24 inches and 30 inches
Expect higher intensity and more even coverage in a grow tent, reflective area or a cross over with multiple lamps.
Power | 60-630 Watts |
Voltage Range | 100-277 VAC 50-60Hz |
LED | Samsung LM301H & Deep Red |
Flowering Footprint | 5' x 5' at 30" |
Veg Footprint | 7' x 7' at 48” |
System PPF Efficacy | 2.81 μmol/joule |
Total output | 1770 PPF |
Dimensions | 26" x 21.25" x 4" |
Recommended Mounting Height | 30-36 inches above canopy |
Conforms to UL Std 1598
Certified to CSA Std C22.2#250.0
View full product details
Optimized for Vertical Rack Grows
$999.00
Refurbished Lamps are tested and fully functional with HLG original components. May have Scratches and/or may have been previously used.
HLG Scorpion Diablo is designed for grows with low ceiling heights or for vertical racks. HLG Scorpion Diablo uses 6x QB648 Diablo Quantum Boards® for an even light spread at just 12" from the canopy. This is a very efficient full spectrum horticulture lamp with an efficiency of 2.9 PPF/W
HLG Scorpion Diablo Manual
Independent Efficiency Lab Report
Independent PPFD Report
Power | 60-650 Watts |
Voltage Range | 100-277 VAC 50-60Hz |
LED | Samsung LM301H & Deep Red |
Flowering Footprint | 5' x 5' at 18" |
Veg Footprint | 6' x 6' at 24” |
System PPF Efficacy | 2.9 μmol/joule |
Total output | 1900 PPF |
Dimensions | 38.5" x 36" x 2.75" |
Recommended Mounting Height | 12-18 inches above canopy |
Watts to BTU Calculator, Cooling Requirement Calculator
*Expect higher intensity and more even coverage in a grow tent, reflective area or a cross over with multiple lamps.
Conforms to UL Std 1598
Certified to CSA Std C22.2#250.0
View full product details
Optimized for Vertical Rack Grows
$799.00
Refurbished Lamps are tested and fully functional with HLG original components. May have Scratches and/or may have been previously used.
HLG Scorpion R Spec is designed for grows with low ceiling heights or for vertical racks. HLG Scorpion R Spec uses 6x 288 Quantum Boards for an even light spread at just 12" from the canopy. QB288 uses Samsung's latest LM301H and Deep Red LED 660nm. This unit is dimmable, with wattage output from 60 to 600 watts.
HLG Scorpion R Spec Manual
Independent Efficiency Lab Report
Independent PPFD Report
Power | 60-600 Watts |
Voltage Range | 100-277 VAC 50-60Hz |
LED | Samsung LM301H & Deep Red |
Flowering Footprint | 5' x 5' at 18" |
Veg Footprint | 6' x 6' at 24” |
System PPF Efficacy | 2.62μmol/joule |
Total output | 1584 PPF |
Dimensions | 38.5" x 36" x 2.75" |
Recommended Mounting Height | 12-18 inches above canopy |
Watts to BTU Calculator, Cooling Requirement Calculator
*Expect higher intensity and more even coverage in a grow tent, reflective area or a cross over with multiple lamps.
Conforms to UL Std 1598
Certified to CSA Std C22.2#250.0
View full product details